Welcome to Thunderdome

Posted: **Tue Mar 20, 2012 9:18 pm**

When I redo my room(s), I'm installing switches like this:

http://www.homedepot.com/h_d1....2995030

I like the built in dimmer. That way, you can turn the lighting down, instead of 'off' if you want it darker for gaming/working/whatever.

Posted: **Tue Mar 20, 2012 9:20 pm**

Oh, also, make sure you have access to your splice boxes. Don't bury them under the drywall. One, it's against code, two, if you need to repair/add/upgrade/change, you won't have to try to remember where it was and cut your wall.

Posted: **Tue Mar 20, 2012 9:33 pm**

Cakedaddy wrote:Oh, also, make sure you have access to your splice boxes. Don't bury them under the drywall. One, it's against code, two, if you need to repair/add/upgrade/change, you won't have to try to remember where it was and cut your wall.

Junction box is in the ceiling, where it will be drop-ceilinged. Any other splices are in the boxes attached to the recessed lighting. I have half a notion to attach another recessed-lighting fixture in the opposite corner of the room, but if I decide to do that I can just run a new line from the existing light at the end of that run. I can do that any time after the room is done.

No other splices.

Posted: **Thu Mar 22, 2012 10:44 pm**

First 4 sheets of drywall went up today... pics later. Thanks to Unk for the extra hands.

Had a sudden horrible thought today... I never tested that HDMI cable, and I have heard of some of them being bad out-of-the-box.

If I enclose it in drywall and it doesn't work, I won't have any way to run a new one on the path it goes in.

This bothers me.

Anyway, I haven't updated the running tally of costs, lately:

New drill bits and electrical odds-and-ends for finishing the electrical portion: $35.
Four sheet of drywall: $35.

Running tally: $1200.

Edited By GORDON on 1332511124

Posted: **Fri Mar 23, 2012 10:00 am**

GORDON wrote:Had a sudden horrible thought today... I never tested that HDMI cable, and I have heard of some of them being bad out-of-the-box.

If I enclose it in drywall and it doesn't work, I won't have any way to run a new one on the path it goes in.

I wonder if I can retrofit some small conduit through the wall, just big enough for the cable.

Posted: **Fri Mar 23, 2012 2:32 pm**

Here are the pics, as promised. Only hung 4 sheets, as I didn't have the energy for more, that day.

East wall, looking east.

NE corner.

NW corner, where my desk will be.

Looking toward SW corner.

The more I think about it, the more I am thinking of running conduit for that HDMI line, in case of it needing replacement. I can get all the conduit for about $20.

Plus conduit is cool.

Edited By GORDON on 1332527588

Posted: **Fri Mar 23, 2012 7:42 pm**

I would drill bigger holes so I could use the broken HDMI as a pull string and pull the new cable. It will be hard to find flex conduit big enough, and you pay a premium for larger diameters. And you are still looking at 1" at least conduit which won't work well if you are making any 90 degree turns around corners.

It's gonna have to be thick because of the ends, and those little round black things that are near the ends. And when you bend conduit, the bend loses some diameter. So, if it's JUST big enough straight, it won't be big enough after you bend it. Even a prebent 90 has a thinner inner diameter.

I think redrilling the holes a little bigger, and angle the hole to follow the cable path (where the cable drops down, angle the hole so it's at a 45 degree angle) would allow you to pull the new cable with the old one.

Posted: **Fri Mar 23, 2012 7:45 pm**

OH, one thing I've learned about doing drywall. . . . there's no such thing as using too many screws. The more you use, the longer it will last without cracking/sagging. My first walls, I didn't use enough screws. The seams would separate and crack. I had to add screws and remud. It hasn't cracked again since. So, use more screws. Then add a few more. And don't skip the middle section. I may be over screwing now. . . but hey, who doesn't like to screw?

I only mention this because counting the screws I can see in your pictures, that's about how many I used on my first rebuilt wall. And it cracked.

Edited By Cakedaddy on 1332546414

Posted: **Fri Mar 23, 2012 9:15 pm**

Cakedaddy wrote:I only mention this because counting the screws I can see in your pictures, that's about how many I used on my first rebuilt wall. And it cracked.

What you see is just enough screws to keep it on the wall.... there will be lots more screws before I mud.

And I bet I can get 1.25" rigid conduit in those studs. They aren't load bearing, so it doesn't matter too much if there is a big weak point where I drill a hole for conduit.

Posted: **Fri Mar 23, 2012 10:44 pm**

You'll be paying a few dollars per foot for it though. If you find it cheaper, post the link. Also, make sure you secure the SHIT out of it. You probably know, flex ain't the easiest to fish, let alone when it's not secure and it bunches up. I am not a fan of flex.

Posted: **Fri Mar 23, 2012 10:47 pm**

Cakedaddy wrote:You'll be paying a few dollars per foot for it though. If you find it cheaper, post the link. Also, make sure you secure the SHIT out of it. You probably know, flex ain't the easiest to fish, let alone when it's not secure and it bunches up. I am not a fan of flex.

Menard's has 8-10 foot sections for about $4 each.

Or maybe it was Home Depot.

Posted: **Fri Mar 23, 2012 10:51 pm**

I didn't mean Rigid conduit, I meant rigid, not flexible.

http://www.homedepot.com/h_d1....d=10051

Posted: **Sat Mar 24, 2012 1:08 am**

OOhhhh PVC. WAY not code. I was going to ask how you were going to fit a 10' stick of conduit between your studs. Same thing applies with the bends being more narrow than the straight pieces.

And actually, as far as it being not code, I'm not really sure what rule you'd be breaking. You can't run high volt through PVC in the walls. But the rules for low volt are so. . . nonexistent that I don't know it's against code. You are just installing a cable chase. Not that it matters to you.

Posted: **Tue Apr 10, 2012 12:52 pm**

Welp, that wall/NE corner is done.

Drywall-is-up-done, I mean.

4 more sheets of drywall, $35.

Running tally: $1235

Posted: **Wed Apr 11, 2012 1:54 am**

Now comes the 4 to 6 weeks of mudding. At least that's how long I spend doing it. It's just never perfect/smooth enough.

Posted: **Wed Apr 11, 2012 7:31 am**

Going to do do that mud/primer mixture idea and see how it works, to add more texture and cover up oopses.

Posted: **Mon Apr 23, 2012 3:36 pm**

Ran some conduit through the half-wall as a cable chase. Had the length of PVC already, and just bought the elbow for the corner. No big whoop. If I ever need to replace that HDMI cable, I will at least have a nice, smooth pipe to get it around that corner. I should be fine, at that point.

Now I just need help getting more drywall into the basement. Volunteers?

Posted: **Thu Apr 26, 2012 3:40 pm**

Still don't have any more drywall so I decided to just finish running conduit to my 2 HDMI access points.

The gap in the conduit is due to the metal wall-supporting beam being in the way. Can't run conduit right there, there's no room.

This is where the HDMI and live electrical used to cross. Now there's a nice conduit separator.

And this is where my desk will be. I decided to make the wall removable under my desk. One won't be able to see it unless they crawl under, and then I can have access to a lot or wiring and conduit and stuff in case I even need to add more lines.

Thinking I am going to bug Unk tomorrow to go pick up some drywall with me.

Posted: **Fri Apr 27, 2012 2:12 pm**

Yay, 4 more sheets of drywall in the basement.

Running tally: $1280.

Posted: **Wed Aug 22, 2012 1:20 pm**

Yes! The thread is being updated!

Those 4 sheets of drywall mentioned above have finally been touched. School is in, summer projects (the ones I had time to get to) are winding down, and I finally have time to get back in the basement. The plan is to have the walls finished before Christmas, and move my existing computer desk down there. This will free up space in our so-called "family room."

Anyway, did this:

Finished drywalling the west wall, where that longish conduit was installed to carry the HDMI cable. So that's done. Tomorrow I hope to finish the south wall, and then assess how much more drywall I will need to finish that phase. And then.... drywall mud and sanding. Then the paint. And I have the perfect color in mind...

Welcome to Thunderdome

Finishing my basement