Rock Climbing Project (Indoors)

For stuff that is general.
Post Reply
TheCatt
Site Admin
Posts: 53729
Joined: Thu May 20, 2004 11:15 pm
Location: Cary, NC

Rock Climbing Project (Indoors)

Post by TheCatt »

Aka: What I did for 4th of July.

I built the kids a vertical 8x8' wall at the start of quarantine. Then built a ceiling-mounted 8x3 to go with it. Since things kept dragging on, decided to build an inclined (more useful) wall. I'd been avoiding it, because drilling + filling 256 holes (in wood) isn't fun. BUT, the gym we are all members of sold us 5 5'x5' panels, pre-drilled, t-nuts installed, pre-finished (textured paint), etc. Professionally made panels for $50 each.

I ordered a bunch of 2x6x10' and waited for the weekend.

I removed the foot-molding, and pulled up the spike strips for the carpet, first.
Image
It's not me, it's someone else.
TheCatt
Site Admin
Posts: 53729
Joined: Thu May 20, 2004 11:15 pm
Location: Cary, NC

Rock Climbing Project (Indoors)

Post by TheCatt »

The area is a 5' vertical wall with a 4' 45 degree wall, so it works out to around a 27 degree wall for a single face.

I attached a footer board to the vertical wall, and a header board to the ceiling, hitting as many joists as I could.

Image

Image
It's not me, it's someone else.
TheCatt
Site Admin
Posts: 53729
Joined: Thu May 20, 2004 11:15 pm
Location: Cary, NC

Rock Climbing Project (Indoors)

Post by TheCatt »

Then I measure where to put the wall joists (measure against the pre-fabricated wall pieces to ensure I did not cover any hold holes), and started hanging joists. Cutting these was a bitch for me, and I ruined the first two. I kept getting the measurements a little off, and they were not snug against, or they were not snug against the footboard.

Image
It's not me, it's someone else.
TheCatt
Site Admin
Posts: 53729
Joined: Thu May 20, 2004 11:15 pm
Location: Cary, NC

Rock Climbing Project (Indoors)

Post by TheCatt »

More joists. I did most of the work myself, so I used the ladder to hold joists in position while I attached them.

Image
It's not me, it's someone else.
TheCatt
Site Admin
Posts: 53729
Joined: Thu May 20, 2004 11:15 pm
Location: Cary, NC

Rock Climbing Project (Indoors)

Post by TheCatt »

Next was blocking. I put them in the middleish, where the top and bottom of the panels would attach later. I'm not good at cutting and placing blocking.

Image
It's not me, it's someone else.
TheCatt
Site Admin
Posts: 53729
Joined: Thu May 20, 2004 11:15 pm
Location: Cary, NC

Rock Climbing Project (Indoors)

Post by TheCatt »

It was warm in the room, so I had the ceiling fans on. Saturday morning I said to myself "I should turn those off, since I'm working on the ceiling."

I did not turn them off.

Image
It's not me, it's someone else.
TheCatt
Site Admin
Posts: 53729
Joined: Thu May 20, 2004 11:15 pm
Location: Cary, NC

Rock Climbing Project (Indoors)

Post by TheCatt »

First panel attached. It was 80 lbs. Carrying it up the stairs sucked. I put a bunch of 2x4s together to lift the panel on to, and then shift it into place.

Image
It's not me, it's someone else.
TheCatt
Site Admin
Posts: 53729
Joined: Thu May 20, 2004 11:15 pm
Location: Cary, NC

Rock Climbing Project (Indoors)

Post by TheCatt »

The 2x4s for mounting.

Image
It's not me, it's someone else.
TheCatt
Site Admin
Posts: 53729
Joined: Thu May 20, 2004 11:15 pm
Location: Cary, NC

Rock Climbing Project (Indoors)

Post by TheCatt »

The top panel was a mere "70lbs" but hard to lift, I leaned it against the ladder, then positioned it on the lower wall segment, and flipped it up. I held it while my wife drilled the first few screws. It was heavy.

Image

Then used a bunch of 3" screws to attach the segments to the joists. End of Saturday.
It's not me, it's someone else.
TheCatt
Site Admin
Posts: 53729
Joined: Thu May 20, 2004 11:15 pm
Location: Cary, NC

Rock Climbing Project (Indoors)

Post by TheCatt »

Sunday was finishing up the 33" section on the right hand side. Basically just a repeat of the prior 2 days, but smaller. The panels at this size were just over 40lbs, and MUCH more manageable.

Image

Finished. Wife for scale.

I hate the small gap between the 33" panels, but I messed up thinking I was cutting the top, but instead cut the bottom, so ooops. Couldn't reverse the panel without covering a bunch of bolt-holes.
It's not me, it's someone else.
TheCatt
Site Admin
Posts: 53729
Joined: Thu May 20, 2004 11:15 pm
Location: Cary, NC

Rock Climbing Project (Indoors)

Post by TheCatt »

A picture showing all 3 surfaces

Image
It's not me, it's someone else.
TheCatt
Site Admin
Posts: 53729
Joined: Thu May 20, 2004 11:15 pm
Location: Cary, NC

Rock Climbing Project (Indoors)

Post by TheCatt »

I don't build stuff, so this was quite a project for me.

Thanks for coming to my TED talk.
It's not me, it's someone else.
GORDON
Site Admin
Posts: 54400
Joined: Sun Jun 06, 2004 10:43 pm
Location: DTManistan
Contact:

Rock Climbing Project (Indoors)

Post by GORDON »

Nice job. The "measure twice/cut once" gets better, the more you do it. But even after all the years, I still cut a piece of trim an inch too short, the other day.

Why didn't you just follow the contour of that wall/roof? Still a challenge.
"Be bold, and mighty forces will come to your aid."
TheCatt
Site Admin
Posts: 53729
Joined: Thu May 20, 2004 11:15 pm
Location: Cary, NC

Rock Climbing Project (Indoors)

Post by TheCatt »

GORDON wrote: Why didn't you just follow the contour of that wall/roof? Still a challenge.
That's what my wife envisioned as well. Because a single face is easier for setting up routes and provides more flexibility. Also, more routes are in the 20-35 degrees of steep than 45 degrees of steep. Also, I would have had to make a lot more cuts of wood, I think.

We can vary the difficulty just by changing the size/spacing/angle of holds

Also, this way I can fix things if they need adjustments in the back.
It's not me, it's someone else.
GORDON
Site Admin
Posts: 54400
Joined: Sun Jun 06, 2004 10:43 pm
Location: DTManistan
Contact:

Rock Climbing Project (Indoors)

Post by GORDON »

Word.
"Be bold, and mighty forces will come to your aid."
TheCatt
Site Admin
Posts: 53729
Joined: Thu May 20, 2004 11:15 pm
Location: Cary, NC

Rock Climbing Project (Indoors)

Post by TheCatt »

GORDON wrote: Word.
Oh, also, it means I can use the electrical outlets behind it. And/or use the storage, or use the back of the wall for storage.

The first and second ones are built against the wall. And about 4 t-nuts have gone bad already. But I cannot access the back, so they cannot be replaced easily :(
It's not me, it's someone else.
TheCatt
Site Admin
Posts: 53729
Joined: Thu May 20, 2004 11:15 pm
Location: Cary, NC

Rock Climbing Project (Indoors)

Post by TheCatt »

GORDON wrote: The "measure twice/cut once" gets better, the more you do it.
I figured I'd mess up the first, so that was fine. The 2nd, I didn't mess up the measurements, but the last trim bit I cut backwards. (I needed to lower the rear about 1/8", lowered the front instead). :evil:

It was fine, I used those two boards to make the blocking.
It's not me, it's someone else.
TheCatt
Site Admin
Posts: 53729
Joined: Thu May 20, 2004 11:15 pm
Location: Cary, NC

Rock Climbing Project (Indoors)

Post by TheCatt »

Project paid off a while ago as the kids used it, but today our oldest qualified 7th in the region (SC and NC) in her age group to qualify for divisiionals (same states plus FL and GA).

(Our youngest quit climbing for swimming cu her favorite coaches quit in the pandemic)
It's not me, it's someone else.
Leisher
Site Admin
Posts: 65258
Joined: Thu May 20, 2004 9:17 pm
Contact:

Rock Climbing Project (Indoors)

Post by Leisher »

I did not know competitive rock climbing was a thing.
“Every record been destroyed or falsified, books rewritten, pictures repainted, statues, street building renamed, every date altered. The process is continuing day by day. History stops. Nothing exists except endless present in which the Party is right.”
Post Reply